¶ 1. How to install the rack for Kobra 3 Max?
Please first put the cylindrical handle into the material rack hole, then rotate it at a certain Angle to fix it, and then press down the assembled material rack and insert it into the left rear card slot of the printer base.
¶ 2. How long does vibration detection take for Kobra 3 Max?
It usually takes about three minutes to complete.
¶ 3.Does it take long for Kobra 3 Max PID correction?
It's usually done in six minutes.
¶ 4. How long does it take Kobra 3 Max to finish automatic leveling?
The machine needs to be preheated and probed, and the whole process takes 10 minutes.
¶ 5. How long does it take for Kobra 3 Max ACE Pro to start up and zero shift?
It usually takes less than a minute to complete.
¶ 6. What is the print size of Kobra 3 Max?
Length/width/height: 420*420*500mm
¶ 7. What is the size of ACE Pro for Kobra 3 Max?
Length/width/height: 366mm(L)*283mm(W)*235mm(H)
¶ 8. Which materials can Kobra 3 Max print?
Kobra 3 Max can print PLA, PETG, ABS, TPU and other linear consumables.
¶ 9. Can Kobra 3 Max be connected to a computer for printing?
In the online state, after the slicing is completed, the Gcode file can be uploaded to the cloud server and pushed to the 3D printer through the cloud server.
¶ 10. What is the maximum Kobra 3 Max nozzle temperature and hot bed temperature?
300 ° C 90 ° C
¶ 11. Does Kobra 3 Max have power off and resume function? Does the machine have a broken material detection function?
Support power off and continue to play function, with broken material detection module (built in the print head)
¶ 12. Is Kobra 3 Max a double Z-axis screw?
The Kobra 3 Max is a dual motor with two screws.
¶ 13. How many languages does Kobra 3 Max support?
At present, the machine supports Chinese, English, German, French, Italian, Spanish, Russian, Japanese, Korean, a total of 9 languages.
¶ 14. What is the print speed of Kobra 3 Max?
The recommended speed is 300mm/s, the acceleration is 10000mm/s2, the specially adjusted small boat printing only takes 18min, the recommended speed is 48min to complete the small boat printing.
¶ 15. How do I load consumables into ACE Pro?
1. Print the cover of ACE Pro;
2. Make sure that the fracture of the materials is neat, straighten the materials, put the materials into the corresponding slot of ACE Pro (divided into 1, 2, 3, 4), and then insert the end of the materials into the corresponding feed port of the slot;
3. Turn on the ACE Pro and confirm that the newly loaded materials can be fed normally.
¶ 16. Is Kobra 3 Max noisy at work?
When the machine prints in accordance with the recommended parameters, the volume generated is about 60 decibels.
¶ 17. Can Kobra 3 Max print ABS?
It can print ABS and PLA, TPU, PETG, but ABS has a high temperature demand, and it needs to be in a constant temperature environment when printing, and it is generally not recommended to print directly. PC, PA, ASA, HIPS, etc. have high temperature requirements, and need to be printed in a constant temperature outer cover environment, and it is generally not recommended to print directly.
¶ 18. What is the role of Kobra 3 Max breaking detection?
During printing, if the materials are insufficient or broken, the machine can detect and automatically stop printing, and can continue printing after replacing with new materials.
¶ 19. When will the part skipping function of Kobra 3 Max be implemented?
The part skip function is still being improved and is expected to be implemented in Q2 2025. When the device pushes the new firmware, you can experience the part skip function after upgrading the firmware online.
¶ 20. What should I do when Kobra 3 Max starts printing the model with uneven bottom thickness?
1. Hold the four corners of the hot bed by hand and gently shake up and down to check whether there is an obvious gap feeling. If there is, tighten the Y-axis pulley under the hot bed (that is, tighten the eccentric nut) to ensure that the hot bed "does not shake and runs smoothly along the Y axis";
2. Hold the print head housing with your hand and gently shake it back and forth to check whether there is an obvious gap. If there is, tighten the eccentric nut of the X-axis to ensure that the print head "will not shake and run smoothly along the X-axis";
3. Hold the X axis by hand and lift the X axis up and down. Observe whether the lead screw coupling and the lead screw are not tightly held, if not tightly held, it is necessary to tighten the coupling screw;
4. Please check whether the two D-shaped wheels inside the Z-axis profile and the four D-shaped wheels outside are idling, if they are idling, it is necessary to tighten the eccentric nut to ensure that the two D-shaped wheels inside "will not idling and run smoothly along the Z axis", and the two groups of D-shaped wheels outside are allowed to idle at most 1 per group.
¶ 21. Will the loose belt of Kobra 3 Max affect the printing?
The loosening of the Z-axis belt may be due to the loosening phenomenon caused by pressing the belt during installation. Under normal circumstances, slight loosening will not affect the running consistency of the belt. If the loosening of the belt affects the operation of the drive wheel, try to loosen the top frame screw, expand the frame outward appropriately and lock the screw to tighten the Z-axis belt.
¶ 22. Why is my Kobra 3 Max printing ABS effect is not good, filaments do not stick to the hot bed?
ABS filaments have higher temperature preservation conditions. It is recommended to preheat the hot bed to 90 degrees and keep it warm for 15 minutes, and then apply solid glue on the surface of the hot bed to increase the adhesion of ABS consumables. If you want to print better, we recommend that the printer be placed in a relatively warm environment for printing, or set up a warm chamber for the printer.
¶ 23.Why does the belt drop slightly after a period of use?
In the early stage, there will be a certain degree of slight wear on the engagement of the new belt and the synchronous wheel, and the wear will be rapidly reduced with the continuous use. This problem will not affect the printing effect, in the regular maintenance of the machine, it is recommended to check the tightness of the belt and the use of the state.