Anycubic Kobra 2 Plus features a 10x faster printing speed, with a maximum print speed of 500mm/s. It outperforms traditional printers, ensuring swift and efficient printing for both large document volumes and urgent printing needs.Featuring a generous 41L printing volume, it provides ample space for printing multiple files at once, eliminating the need for frequent paper changes or page adjustments, saving time and effort.
Our product stands out with its smart and user-friendly design. With an intuitive interface, anyone can easily master its operation. No complex setup required – just a few simple steps to achieve high-quality printing.
Official product page: Anycubic Kobra 2 Plus
¶ User Manuals
¶ Product Details
¶ Printer Manuals
- Assemby
- Manual
- Leveling Calibration Guide
- Basic Slicing Software Operation Guide Video
- How To Change Filament During The Printing Process
- Camera Installation Guide
¶ Setting up
- PrusaSlicer
- Please note：For the use of files, please refer to the document PrusaSlicer Installation And Parameter Import Guide V1.1
- Download：Filaments for PrusaSlicer Settings
- Ultimaker Cura
- Download: Filaments for Cura Settings
- AnycubicSlicer
- Please note：
After repeated testing, Anycubic has provided filament profiles for the machine in the AnycubicSlicer to achieve the best printing results.
Additionally, some capacities are exclusively available within the AnycubicSlicer.
Thus, we highly recommend using AnycubicSlicer.
lf still preferring to use Prusa Slicer or Cura for slicing, please use the official recommended configuration files to achieve better printing results.
- Please note：
¶ Troubleshooting
- Kobra 2 Plus FAQ
- Leveling Calibration Guide
- Unable to recognize USB
- Poor Print Quality
- Device Unable to Connect to the Network
¶ Device Abnormality Popup
- Prompt“Hotbed NTC abnormal, please check it and wiring”
- Prompt“Hotbed heating abnormally, please check it and wiring”
- Prompt“Nozzle NTC abnormal, please check it and wiring”
- Prompt“Nozzle heating abnormally, please check it and wiring”
- Prompt“The module is abnormal. Please calibrate the position of the nozzle and module”
¶ Maintenance
¶ Kobra 2 Plus
¶ Control Screen
¶ Limit Switch
¶ Tensioning Rod
¶ Motherboard
¶ Hotend
¶ Hot Bed
¶ Extruder
¶ X-Axis
- X-Axis Rails Replacement Guide
- X-Axis Pulley Replacement Guide
- X-Axis Belt Replacement Guide
- Replacement X-Axis Motor
¶ Y-Axis
- Y-Axis Rails Replacement Guide
- Y-Axis Belt Replacement Guide
- Y-Axis Pulley Replacement Guide
- Replacement Y-Axis Motor
¶ Z-Axis
- Z-Axis Timing Belt Replacement Guide
- Replacement Z-Axis Motor
- Replacement Z-axis Motor Bracket
- Z-Axis Lead Screw Replacement Guide
¶ Power Supply
¶ Offset Measurement Switch
¶ Print Head
- Print Head Teflon replacement Guide
- Print Head Adapter Board Replacement Guide
- Print Head Module Replacement
- Hot End Heating Rod
- Hot End Temperature Sensitive Wire
- Replacement Print Head Cooling Fan
- Replacement Model Cooling Fan
¶ WiFi Antenna
¶ Silicone Sock
¶ Filament Sensor
¶ Download Center
¶ Firmware
¶ Manual
- Kobra 2 Plus_User Manual_v1.2_EN
- Kobra 2 Plus_User Manual_Quick Start Guide_v1.0_EN
- PrusaSlicer Filaments Profiles
- Cura Filaments Profiles
¶ Slicer Software
¶ Test Files
- Proximity switch.gcode
- Please operate on the printer: "Print" ➡ "" Local "➡" Test Model ". And you could use the test model.